Bushing washers are round metal washers that fit under skateboard bushings on each truck, and are installed by simply sliding them on the kingpin. The purpose of bushing washers is to prevent the bushings from getting deformed by the pressure exerted on the trucks.
Are skateboard washers necessary?
Do you need washers for skateboard bearings? Normal skate bearings need speed washers (or “speed rings”) to stop the bearing from fouling on the axle nut or the hanger face. Some trucks also don't have enough thread on the axle to tighten the nuts down enough if you don't have speed rings.
Do you need the top washer for bones bushings?
Although you can still use the washers provided with your trucks, you might not see the full benefit of the Bones Bushings. The bottom bushing is designed to just sit on the baseplate. The top bushing is secured with a large washer (provided).
What are skateboard bearing washers for?
Problems Without Spacers
Includes 8 axle washers enough to outfit 2 skateboard trucks. Speed washers increase speed and promote longer bearing life by reducing friction between the bearing and axle nut and hangar. They also help to protect your bearings from dirt and debris.
Should you grease skateboard bushings?
A good thing to do is put a smear of grease, oil, WD40 or dry lube stick on the top and bottom flat surface of the bushings. This just helps the hanger 'slip' back to it's correct position. If you ride your trucks a bit they will 'break in' and it will probably sort it's self out pretty quickly.
30 related questions foundCan you use WD 40 on skateboard trucks?
You should never use WD40 to clean skateboard bearings . This is a product designed specifically made for removing rust and grime, not as a lubricant or cleaner for bearings. It works wonders at first, but you'll find yourself reapplying more and more as it dries out bearings.
How do you break in skateboard bushings?
Spend your first few skate sessions either skating on flat ground or basic riding in a mini ramp. Adjust the trucks after a few days of breaking in the new bushings. As soon as your board starts to feel normal—no tightness or awkward pulling off to one side—tighten the trucks as you would normally ride them.
Do I need washers on skateboard trucks?
Once all four wheels have their two bearings each, it's time to attach them to the trucks. To set yourself up, set the skate on its side again. Most trucks come with two axle washers per wheel, for a total of eight. These washers should go on either side of wheel to help it spin smoothly.
Do I need washers on my roller skates?
Washers are needed in roller skates because they prevent bearings from rubbing up against the hanger and axle nut. Washers help provide the rider with a smooth ride while using a roller skate.
Do you need spacers and washers for skateboard bearings?
Bearing spacers are totally optional; longboarders and casual skaters likely won't put enough pressure on their boards to ever need them, though they are definitely a good investment if you want to slide, do a lot of tricks, and generally skate hard.
Are bones hard bushings good?
The hard bushings from Bones are perfect. They definitely stiffened up the trucks and hold up to my ollies. If you want stiff trucks and/or need something heftier to put up with extra weight, these are perfect.
Do Bones bushings break in?
With BONES Bushings™, you will notice a number of positive improvements in the performance of your trucks. There is no break-in period. Just put them in, adjust and skate. Your trucks will be more responsive.
Do bearing spacers slow you down?
This will slow your bearings down and wear them out super fast! Skaters without bearing spacers might find it easier to just run their axle nuts a bit loose to keep the wheels spinning freely. This is even worse! A wheel that is loose on the axle will give a noisy, chattery ride.
Can I skate without speed rings?
Speed Rings are an often overlooked part of your skateboard, but not having them could be greatly jeopardizing your performance! Speed rings go on the outside of your bearings to give more clearance, allowing an uninhibited continuous roll.
Do I need spacers in my skateboard wheels?
Bearing spacers are totally optional; longboarders and casual skaters likely won't put enough pressure on their boards to ever need them, though they are definitely a good investment if you want to slide, do a lot of tricks, and generally skate hard.
How tight should skateboard wheels be?
Your skateboard wheels should be tight enough that they spin freely. However, you don't want the wheels so loose that they wiggle on the truck's axle. To see if you need to tighten your wheels, put the board on its side, and flick the wheel as fast and as hard as you can with one hand.
Do you need spacers for roller skates?
Spacers are used in skates, scooters, waveboards and pretty much anything that rolls with bearings. You should always use the right kind of spacers with your wheels. If you don't use spacers, the bearings can be excessively stressed, roll badly and end up breaking in a short time.
What are the washers on skateboard trucks?
Speed washers increase speed and promote longer bearing life by reducing friction between the bearing and axle nut and hangar. These washers are the standard size and will fit on all skateboard/longboard trucks that have 8mm axles (virtually every truck has the standard 8mm axle size).
Which way should skateboard trucks face?
Longboard trucks are usually reversed kingpins (the center bolt on which the hanger pivots), meaning the kingpin faces outwards. Standard kingpin trucks for short boards sit with the screw facing inside to protect it from grinds and whatnot.
Do Bones Reds come with spacers?
Includes a set of 8 Bones Reds Bearings, 8 Speed Washers, and 4 Bearing Spacers. Instructions and Sticker are included in the box of Bones Reds Bearings. Bones Reds Bearings fit all skateboard wheels.
Do all bushings fit all trucks?
All trucks come with stock bushings, but some prefer to replace them. Not everybody weighs the same and skaters prefer different tightness on the trucks. Note that bushings need to break in a little before you can tell you want to replace them.
Do I need new bushings skateboard?
Bushings commonly get worn out over time and start making your trucks floppy and unstable, which can cause you to get a lot of wheelbite. If your bushings are split or crushed on one or both sides, it's probably worth replacing your bushings so you can get some more responsive turns and less flop.
How can I make my bushings softer?
Simply screw them back on with the skate tool or wrench and the bolt. Start skating. You should notice a difference immediately. Riding the board right after you put them on will preserve the softness and allow them to loosen up even more.
